how hard is it to cross-compile x86_64 rust to aarch64?

Software Development

Cross‑Compiling Rust from x86_64 to aarch64

Cross‑compiling Rust is trivial for pure‑Rust crates but can become challenging when the project depends on C libraries or complex build scripts. Below is a practical guide that categorises the difficulty levels, recommends tooling, and highlights common pitfalls.

1. Difficulty Levels

LevelTypical SituationRequired Steps
**Easy** (Pure Rust)No C dependencies, no custom build scripts1. Add the target: rustup target add aarch64-unknown-linux-gnu
  1. Build: cargo build --target aarch64-unknown-linux-gnu | | **Moderate** (Standard Dependencies) | Crates that need an external linker (e.g., openssl, libz) | 1. Install a cross‑linker (e.g., gcc-aarch64-linux-gnu on Ubuntu).
  2. Configure Cargo to use it via .cargo/config.toml. | | **Hard** (C/C++ Dependencies) | Libraries that require system headers or custom C code (e.g., OpenSSL built for aarch64) | 1. Build or obtain cross‑compiled versions of the required C libraries.
  3. Ensure the cross‑linker can locate those libraries. |

2. Recommended Toolchains

2.1 cross

cross is the de‑facto solution for most Rust cross‑compilation scenarios. It runs builds inside Docker containers that already contain the appropriate toolchains, linkers, and C libraries for virtually any target, including aarch64-unknown-linux-gnu.

cross build --target aarch64-unknown-linux-gnu

Pros: No manual installation of cross‑linkers; works out‑of‑the‑box for many crates. Cons: Requires Docker (or Podman) and may add a small runtime overhead.

2.2 cargo-zigbuild

cargo-zigbuild leverages the Zig compiler as a linker. Zig bundles many C headers and provides a self‑contained cross‑linking environment, often simplifying builds that would otherwise need a full GCC toolchain.

cargo zigbuild --target aarch64-unknown-linux-gnu

Pros: Minimal external dependencies; fast linking. Cons: Still experimental for some targets; may need manual Zig installation.

3. Common Hurdles and How to Resolve Them

3.1 The Linker Issue

Rustc can emit aarch64 object files, but by default it invokes the host’s x86_64 linker, which cannot produce aarch64 binaries. Explicitly specify a cross‑linker:

# .cargo/config.toml
[target.aarch64-unknown-linux-gnu]
linker = "aarch64-linux-gnu-gcc"

If you use cross, the correct linker is selected automatically.

3.2 Build Scripts (build.rs) and Procedural Macros

Crates that contain a build.rs script or procedural macros are compiled for the host (x86_64) because they must run during the build. The main library is then compiled for the target (aarch64). Ensure the host toolchain can compile those scripts; otherwise you’ll see “cannot find crate for std” errors.

3.3 libc Version Mismatch

The target system’s glibc version must be equal to or newer than the version used by the cross‑compiled binaries. If you compile against a newer glibc than the target provides, you’ll encounter runtime errors such as “GLIBC_2.28 not found”. To avoid this, either:

  • Build against the oldest glibc version you need to support, or
  • Use a Docker image that matches the target’s distribution (e.g., debian:buster for older glibc).

4. Quick Start Checklist

  1. Choose a tool – cross for simplicity, cargo-zigbuild for a lightweight alternative.
  2. Install Docker/Podman if using cross.
  3. Add the Rust target: rustup target add aarch64-unknown-linux-gnu.
  4. (Optional) Install a native cross‑linker (gcc-aarch64-linux-gnu) if you prefer not to use Docker.
  5. Configure Cargo (only needed for native cross‑linkers).
  6. Build: cross build --target aarch64-unknown-linux-gnu or cargo zigbuild ….
  7. Test the resulting binary on an aarch64 device or emulator.

Back to all articles